Hey fellow self-hosting lemmoids

Disclaimer: not at all a network specialist

I’m currently setting up a new home server in a network where I’m given GUA IPv6 addresses in a 64 bit subnet (which means, if I understand correctly, that I can set up many devices in my network that are accessible via a fixed IP to the oustide world). Everything works so far, my services are reachable.

Now my problem is, that I need to use the router provided by my ISP, and it’s - big surprise here - crap. The biggest concern for me is that I don’t have fine-grained control over firewall rules. I can only open ports in groups (e.g. “Web”, “All other ports”) and I can only do this network-wide and not for specific IPs.

I’m thinking about getting a second router with a better IPv6 firewall and only use the ISP router as a “modem”. Now I’m not sure how things would play out regarding my GUA addresses. Could a potential second router also assign addresses to devices in that globally routable space directly? Or would I need some sort of NAT? I’ve seen some modern routers with the capability of “pass-through” IPv6 address allocation, but I’m unsure if the firewall of the router would still work in such a configuration.

In IPv4 I used to have a similar setup, where router 1 would just forward all packets for some ports to router 2, which then would decide which device should receive them.

Has any of you experience with a similar setup? And if so, could you even recommend a router?

Many thanks!

Edit: I was able to achieve what I wanted by using OpenWrt and their IPv6 relay mode. Now my ISP router handles all IPv6 addresses directly, but I’m still able to filter the packets using the OpenWrt firewall. For IPv4 I didn’t figure out how to, at the same time, use the ISP’s DHCP server, so I just went with double NAT. Everything works like a charm. Thank you guys for pointing me in the right direction.

  • robber@lemmy.mlOPEnglish
    1·
    2 months ago

    And openwrt is capable enough?

    Yeah it’s insane right? Every address is reachable when I open a port range. And it’s like there are ~ 10 predefined services (HTTP/S, SMTP, …) and the category “All other ports” where also 22 is part of. So I really have the choice to either keep everything shut or leave everything wide open.

    I think I can’t use my own modem but I’ll have to double check with my ISP. But yes the Wi-Fi is also provided by that router and it’s also quite crappy.

    • Max@lemmy.worldEnglish
      2·
      2 months ago

      Yeah openwrt should be great. It uses nftables as a firewall on a Linux distribution. You can configure it through a pretty nice ui, but you also have ssh access to configure everything directly if you want.

      The challenge is going to be what the ISP router supports. If it supports bridge mode then things are easy. You just put your router downstream of it and pretend like it’s a modem. Then you configure openwrt like it’s the only router in the network. This is the opposite of what you’ve suggested, using the upstream ISP router in pass through and relying on the openwrt router to get the ipv6 GUA prefix. (You might even be able to get a larger prefix delegated if you set the settings to ask for it)

      If you don’t have bridge mode then things are harder. There’s some helpful information here https://forum.openwrt.org/t/ipv6-only-slaac-dumb-aps/192059/19 even though the situation is slightly different since they also don’t want a firewall. But you probably need to configure your upstream side on the openwrt router similarly.

      Also looking more, the tplink ax55 isn’t supported by openwrt. If you don’t already have it, I’d get something that does. (Or if the default software on the ax55 supports what you want, that’s fine too. I just like having the full control openwrt and similar gives)

      • robber@lemmy.mlOPEnglish
        1·
        2 months ago

        That’s really helpful, thank you. I’ve ordered an AX23 which will arrive tomorrow. I’ll try to figure it out in the next few days and report back.