First seeing this on my home feed on Jan 7th. Relieved to find the post is 5 days old…

Oops ;-)

Clocking in at 37 minutes. Don’t judge prog by the number of tracks… pretty typical album runtime for anything released in the vinyl era.

Also, it’s fantastic.

You mention frigate specifically. Were you running this on the system when the drive failed, or is this a future endeavour?

I bring this up because I also use frigate, and for some time I was running with a misconfigured docker compose that drove my SSD wearout to 40% in a matter of months.

Make sure that the tmpfs is configured per the frigate documentation and example config. If misconfigured like mine was, all of that IO is on disk. I believe the ramdisk is used for temp storage of camera streams, until an event occurs and the corresponding clip is committed to disk.

Good luck!

That’s great. Thank you again!

Thank you! Something concrete to go on. Is there a specific name these go by? I couldn’t find them by searching.

I think I have two issues to work through. I’m not sure I applied enough pressure to actuate the spring (access may be a limiting factor in-situ), and I was using an extremely fine gauge of wire. I doubt it would have the stiffness to push in.

Would a stalk lug work to provide added stiffness to the conductor, or does this terminal expect something malleable?

That was my initial thought, but there’s little to no give in the orange button. If anything it only felt like a little play you get between loosely coupled mechanical pieces. That’s when I tried operating it like a clamp and broke one off.

Pulling around 200W on average.

• 100W for the server. Xeon E3-1231v3 with 8 spinning disks + HBA, couple of sata SSD’s
• ~80W for the unifi PoE 48 Pro switch. Most of this is PoE power for half a dozen cameras, downstream switches and AP’s, and a couple of raspberry pi’s
• ~20W for protectli vault running Opnsense
• Total usage measured via Eaton UPS
• Subsidised during the day with solar power (Enphase)
• Tracked in home assistant

Looks like home assistant

For storage redundancy RAID 5 is not recommended, particularly as you get to high capacity drives (think >8TB). I think the rating to consider is URE (unrecoverable read error, usually 1 in 10^14 bits read).

Once a drive inevitably fails and you are forced to resilver the array to avoid data loss. During the resilver the healthy disks are running at 100%, reading every bit of data they have to complete the parity calculation and determine what data is missing. The chances of encountering a URE on another drive is a near certainty at high capacities as the total number of bits read exceeds the URE rating. As result the resilver would fail and the array would be lost.

RAID 6 as a minimum (2 drive redundancy), although a popular option now (and the layout I use) is mirrored vdevs.

Edit: Consider TrueNAS for NAS software. I have been using it for 10 years and it is absolutely rock solid. 25TB usable storage across 4x mirrored vdevs. I run it as a VM inside Proxmox with 4 logical cores on a 10 year old Xeon with 16GB RAM for the VM (I run ECC as was recommended at the time, but whether it’s still considered necessary I’m not certain).

I would also recommend getting an LSI HBA (host bus adapter) like the 9207-8i flashed to IT mode (it must not be in raid mode, let TrueNAS manage the disks directly). This simplifies passing through all the disks to a VM.

The options I’m looking at have PCIe 4 and seem to be gen 2? Epyc 7282 or 7302.

I think this is where I’m headed. Is there anything to consider with Threadripper vs Epyc? I’m seeing lots of CPU/MOBO/RAM combo’s on ebay for 2nd gen Epyc’s. Many posts on reddit confirming the legitimacy of particular sellers, plus paypal buy protections have me tempted.

Thanks, I’ll need to have a look at how the chipset link works, and how the southbridge combines incoming PCIe lanes to reduce the number of connections from 24 in my example, to the 4 available. Despite this though, and considering these devices are typically PCIe 3.0, operating at the maximum spec, they could swamp the link with 3x the data it has bandwidth for (24x3.0 is 23.64GB/s, vs 4x4.0 being 7.88GB/s).

This is what I do as well. I have a public DNS record for my internal reverse proxy IP (no need to expose my public IP and associate it with my domain). I let NPM reach out to the DNS provider to complete verification challenge using an account token, NPM can then get a valid cert from Let’s Encrypt and nothing is exposed. All inbound traffic on 80/443 remains blocked as normal.

The icing on the cake for me is the empty “Neat Patch” above the switches

Thanks. This is a pretty compelling option. I hadn’t looked at the entry level arc, but when it comes to encode/decode it seems all the tiers are similar. 30W is okay, and it’s not a hard limit or anything, just nice to keep bills down!

I hadn’t considered AMD, really only due to the high praise I’m seeing around the web for QuickSync, and AMD falling behind both Intel and nvidia in hwaccel. Certainly will consider if there’s not a viable option with QS anyway.

And you’re right, the south bridge provides additional PCIe connectivity (AMD and Intel), but bandwidth has to be considered. Connecting a HBA (x8), 2x m.2 SSD (x8), and 10Gb NIC (x8) over the same x4 link for something like a TrueNAS VM (ignoring other VM IO requirements), you’re going to be hitting the NIC and HBA and/or SSD (think ZFS cache/logging) at max simultaneously, saturating the link resulting in a significant bottleneck, no?

Thanks. I’ll be the first to admit a lack of knowledge with respect to CPU architecture - very interesting. I think you’ve answered my question - I can’t have QuickSync AND lanes.

Given I can’t have both, I suppose the question pivots to a comparison of performance-per-watt and number of simultaneous streams of an iGPU with QuickSync vs. a discrete GPU (likely either nVidia or Intel ARC), considering a dGPU will increase power usage by 200W+ under load (27c/kWh here). Strong chance I am mistaken though, and have misunderstood QuickSync’s impressive capabilities. I will keep reading.

I think the additional lanes are of greater value for future proofing. I can just lean on CPU without HWaccel. Thanks again!

I use the Amplipi from Micro-Nova for whole-home audio and I love it. It’s local, open source and has a Home Assistant integration.

The main unit has 6 zones, but expansions units can be added. I think it supports up to 4 simultaneous streams. We use 2x AirPlay streams, and a turn table connected via RCA, but many other options are supported. They detail it all on their website and GitHub repo.